Migration emergency - clocks ticking!
I'm trying to follow the migration article
I have a disk image, swap image, regular configuration and Finnix recovery configuration, which is currently booted. When I try to load the console, I get this:
md: multipath personality registered for level -4
unknown partition table
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Starting balanced_irq
Using IPI Shortcut mode
blkfront: xvdc: barriers enabled
xvdc: unknown partition table
XENBUS: Device with no driver: device/console/0
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
VFS: Mounted root (iso9660 filesystem) readonly.
Freeing unused kernel memory: 212k freed
Write protecting the kernel text: 2568k
Write protecting the kernel read-only data: 605k
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
EDIT: I panicked, due to my tight schedule. I simply forgot to add the uncompressed initrd image to the configuration. Problem solved.
9 Replies
Me neither.
It's like those guys can't get past Chapter 2 of "Marketing for Dummies"
When I got to the point of chroot'ing in the howto, it gave me the following error:
chroot: cannot run command `/bin/bash': Exec format error
It let me run the mknod commands though so I figured it might work regardless. Rebooted into the default configuration, and tried to bring up ssh with no success, so I loaded the AJAX console and got the following:
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
ebt_ulog: not logging via ulog since somebody else already registered for PF_BRIDGE
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>All bugs added by David S. Miller <davem@redhat.com>SCTP: Hash tables configured (established 16384 bind 16384)
Using IPI Shortcut mode
XENBUS: Device with no driver: device/console/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 224k freed
request_module: runaway loop modprobe binfmt-464c
request_module: runaway loop modprobe binfmt-464c
request_module: runaway loop modprobe binfmt-464c
request_module: runaway loop modprobe binfmt-464c
request_module: runaway loop modprobe binfmt-464c</davem@redhat.com></greearb@candelatech.com>
Should I be starting this whole process over again?
@vonskippy:
What? You didn't stick around to hear Slicehost's big mystery February announcement?
Me neither.
Oh yes, that was supposed to be this month wasn't it? Pickled made it fairly obvious that the changes coming were probably not going to benefit any of us little fella's anyways.
Since I won't be spinning out a half dozen 1440's this weekend just to deal with a lunch hour rush, I don't feel like he cared about me.
Linode just feels more like home.
I now know that for my purposes 32 bit is better. The problem is I think that caused the migration to fail using the rsync method, but I'm not sure.
I'd rather be using 32 bit. Is there any way I can pull this off?
-r-------- 1 root root 140737486266368 2010-02-07 22:58 kcore
I wish I had that much memory.
Setup a Linode with the 32 bit distro of your choosing.
Install whatever apps you need.
Get everything working all by itself on the new VPS.
Then copy your config files over.
Then snapshot your database(s) and move them over.
Then drink a beverage of your choice.
Trying to copy everything over - especially going from 64bit to 32bit just won't work.
My database and post office are already hosted on seperate nodes, so thankfully I haven't done any damage to them throughout this whole process.
I just stumbled across the article and thought hey! Snazzy quick!
So I think now I'm just going to set it up from scratch, tarball all my sites, and just wget them over the airwaves like I had originally planned. I think part of me wanted to do this to learn how.